Rear Ends Circle Track

Qty:	^$400.00	1000-001-1 Track 9 Style 60" x 30" x 30" GN Housing	58 Lbs.

Qty:	^$375.00	1000-001-1 MB9 Style 60" x 30" x 30" GN Housing	58 Lbs.

*Complete Floater Housing Kit*
$1102.00 Complete Track 9	$1078.00 Complete MB9
		Housing kits come complete with the following: Welded bare floater housing, 58" to 62" wide. 2ea. 31 spline axles 2 complete hub kits as follows; 2ea. 5 x 5 Standard Steel Hub with studs and race installed. 2ea. Standard Aluminum Drive Flange & O-ring. 2ea. Steel Brake Rotor Adapter. 2ea. Inner and 2ea. Outer Bearings. 2ea. Inner Seals. 2ea. Aluminum Caps with O-rings and Screws. Rotor Mounting Hardware.
			Specify left and right dimensions when ordering.

Please call to talk to One of Knowledgeable Sales Staff to order your custom housing Kit

Brake Rotors / Adapters

$45.00ea. STANDARD

$45.00ea. LIGHT WEIGHT

$25.00ea. STEEL or ALUMINUM

Standard Brake Rotors are

11.75" Diameter and 1.25" Thick

Light Weight Brake Rotors are 11.75" Diameter and .810" Thick

Available in Steel or Aluminum with your choice of bolt pattern.

8 Holes on 7" Bolt Circle

10 Holes on 6.8" Bolt Circle.

Qty:	^$45.00	1400-532 Standard Steel Vented Rotors 1.25" Thick	10 Lbs.

Qty:	^$45.00	1400-533 Light-Weight Steel Vented Rotors .815" Thick	9 Lbs.

Qty:	^$30.00	1400-003-A Aluminum 8 Hole x 7" B.C. Rotor Adapter	2 Lbs.

Qty:	^$30.00	1400-003-S Steel 8 Hole x 7" B.C. Rotor Adapter	4 Lbs.

Qty:	^$30.00	1400-002-A Aluminum 10 Hole x 6.800" B.C. Rotor Adapter	2 Lbs.

Qty:	^$30.00	1400-002-S Steel 10 Hole x 6.800" B.C. Rotor Adapter	4 Lbs.

Qty:	^$5.00	1400-504-13 Rotor Bolt Kit	1 Lbs.

Floater Rear End Narrowing Kits

CIRCLE TRACK FLOATER NARROWING KIT INCLUDES:

72" Line Up Bar

Ford Carrier Bearing Line Up Blocks ( specify size )

Centering Plate

Snout alignment Rings

Tube Line Up Rings

Narrowing a rear housing for your circle track car is breeze with this kit. An 1-1/2" x 72" precision ground line up bar is passed through the banjo section and through the carrier bearing support blocks. This give you the absolute rear axle center line. The tubes, with the snouts already welded into them, are then slipped over the tube line up blocks and then slid onto the shaft. The snout rings are then inserted into the ends of the snouts. This provides you with a very true and square installation.

Qty:	^$400.00	1000-RENK2 Circle Track Floater Housing Narrowing Kit	70 Lbs.

*Seals-it*

	9" Ford Inner Axle Seal - This billet aluminum seal has three O-rings that seal it to the axle tube and two bonded, heavy duty, neoprene inner seals designed to compensate for any amount of axle shaft.

Qty:	^$56.00	Gold #AS9520 2.500" OD	2 Lbs.

Qty:	^$56.00	Blue #AS9218 2.560" OD	2 Lbs.

Qty:	^$56.00	Red #AS9188 2.625" OD	2 Lbs.

Qty:	^$56.00	Silver #AS9125 2.750" OD	2 Lbs.

*Axles*
		We have a large selection of axles in stock for immediate shipping. If we don't have what you need we'll get it.

Grand National Double Spline $105.00

Lite Weight Gun Drilled $160.00

Please Call For Your Specific Application

Rear Snout GN 5 x 5

click for measurements

We machine these snouts in house to exacting tolerances from premium steel blanks. The inside of the snouts is tapered bigger on the housing side to smaller on the outer end. This taper provides a lite weight yet strong piece. We see tubes totally ripped away or folded over from wrecks and the snout is intact, RACE PROVEN PARTS! Some of the largest suppliers in the country use our housings and snouts.

Qty:	^$^48.00	800-004-L Left GN Weld In Snout	4 Lbs..
Qty:	^$48.00	800-004-R Right GN Weld In Snout	4 Lbs..

*Pinion Angle Plate*
	3rd Member not included	Smart Tool & 3rd Member not included	This great little item gives you a quick and simple method of knowing and setting your pinion angle. Use this when first setting up your chassis or when making changes. This will allow you to keep and maintain this critical angle. Just bolt the plate to the right side third member studs and then you can use your digital level to set your pinion angle.

Qty:	^$^17.50	1000-310 Pinion Angle Plate	1 Lbs..

Privacy & Security

Tube Notchers	Tube Benders	Bead Rollers	Rotary Machines	Sheet Metal Tools	Rear Ends	Specialty hand Tools	Tech Support	Movies Index	Articles & Links
	Welcome	About Us	Services	Contact Us	Terms	Tanner by MB	MB Motorsports	Industrial Machines

sales@mittlerbros.com

Revised: April 22, 2008

*Bare Floater Housings*
$400.00 Track 9 Style	*$375.00 MB9* Style**
		Housings are constructed from new TRACK 9 Standard banjos or MB9 Banjos and new 3" x 3/16" wall tube. New 5 x 5 snouts are pressed in and trued up. They are then precision MIG welded. Next the welds are turned down in a lathe to match the tube so you can slide your hardware on without difficulty. The tubes are then inserted into the banjo section and lined up with fixtures and welded. Each housing is built your specs or you can order one of our more popular 60" x 30" x 30" housings from stock. Specify left and right dimensions when ordering.